-
Yamaha RD350/400/250 Oil Line Clamp. Genuine Yamaha OEM part. Sold each. In original black oil finish, no longer available from Yamaha.
-
Y-boot Adaptors for Larger Mikuni Carburetors
- Install a Y-boot Filter kit on your Yamaha RD with Larger Carburetors
- Increase performance by reducing turbulance generated from pod filters
- Adapts our Y-boot filter kit to fit the larger aftermarket Carbs with a 58mm inlet housing
- Mikuni VM30-34
- Mikuni TM32-34
- Includes 2 adaptors and 2 clamps
- Made from Aluminum. In Lincoln NE, USA
- Sold as a pair
-
Brass T-Splitter 1/4"
- Use to route or repair fuel lines, oil lines and air lines
- Barbed ends provide a secure fit
- Made in the U.S.A.
-
Carb Top Boots - Yamaha 1979 RD400F Daytona. Theses are the accordion type rubber boots that go on top of the Daytona carbs. Sold in pairs, reproduction part. Originals no longer available from Yamaha. 2V0-14169-00-00
-
Carburetor Needle Clip for VM, TM or TMX Mikuni carburetors. Sold each. BS32/126
-
Carburetor Top Cable Adjuster - Mikuni. For Mikuni VM carburetors. Sold each. Available in 6mm or 7mm (RD/RZ/R5). Note: 7mm does not include nut. Choose size and quantity, then click add to cart.
-
VM28 Choke Lever Assembly - Genuine Mikuni. Includes 1x each the following parts / part numbers:
- Lever - 360-14175-00-00
- Nut - 278-14174-00-00
- Plate - 170-14178-00-00
- Choke Plunger - 278-14171-00-00
- Plunger Spring - 256-14135-00--00
- O-ring - 93220-09001-00-00
- Choke Plunger Cap - 802-14173-00-00
-
Carburetorย Chokeย Plungerย by Mikuni for VM24-28mm carburetors. Sold each.
-
Float Bowl Drain Washer (gasket) for VM28mm Roundslide carburetors - RD350/RD250/R5 (all) Sold each. Genuine Mikuni
-
Float Bowl Drain Washer - RD350/RD250/R5 (all) Sold each. OEM part no. 278-14117-00-00
-
Float Bowl Drainย Washer - RD400 (76-79). This Viton O-ring is a perfect replacement for the original gasket which has been discontinued by Yamaha.
-
Float Bowl Screw for VM24-28mm carburetors. Sold each. Note threaded portion of screw is 15mm (slightly longer then original screws used on RD's, but works fine).
-
Float Bowl Screw set for VM24-28mm carburetors. Sold as a set of 4 screws with lock washers (enough to do one carburetor). Note threaded portion of screw is 14mm (same as original screws).
-
Genuine Mikuin Vent Line, sold each, precut from Mikuni in approximately 11.5" sections, transparent pink color.
-
2 Stroke Oil Injector Nozzle - RD250/350/400 (carb oil injector nozzle). Economy Cycle reproduction item, no longer available from Yamaha. Sold each.
-
Jet Needle Shim for Mikuni 5 Series Jet Needles. Sold each. These shims are used to make incremental adjustments between clips on jet needles used on Mikuni VM carbs with series 5 jet needles (5DP7, 5L1, etc.).
-
Main Jet Washerย by Mikuni for VM24-28mm carburetors. Sold each. This washer seats under the main jet (on bottom of needle jet).
-
Mikuni Vent Tube Anchor Plate - This part attaches to the float bowl screws and holds the vent line. 2 Required per carb.
-
Genuine Mikuni Float Needle Valve Seat Washer for RD250/350/400/R5/DS7 & all VM(24-30mm) Carbs. Sold each.
-
Oil Injection Line Clip, 90468-02033-00 OEM Originals $6.99 each or Reproduction Clips - $1.95 each
-
Fuel Rated Plastic T-Splitter 1/4"
- Use to route or repair fuel lines, oil lines and air lines
- Barbed ends provide a secure fit
- Made in the Germany
-
Brand new fresh rubber carburetor boots for Yamaha RD350 and R5. Boots protect the carbs and cables from dust, dirt and moisture. These boots go on top of the carbs where the cable enters the slide. These are not the boots that connect the carbs to the air filter box. These are suitable for any round slide carb for street and dirt motorcycles. Sold in pairs.
-
Yamaha RD250/350 Carburetor Boot for Low Top Carburetor, sold each. Yamaha OEM part.
-
RD250/350 Idle Screw / Spring Assembly. Includes Screw & Spring. By Mikuni. This is also the correct idle screw/spring for the new Mikuni VM28's.
-
RD250/350 Idle Screw / Spring Assembly. Includes Screw & Spring. OEM Yamaha
-
Yamaha RD250/350/400/R5/DS7 Rubber Choke Plunger Cap (COVER, PLUNGER CAP) reproductin replaces OEM # 802-14173-00-00, sold each
-
RD400 (1976-1978 C/D/E) Idle Screw / Spring Assembly. Includes Screw, oring & Spring. OEM Yamaha 4AC-14103-00-00
-
Yamaha RD400 C/D/E Throttle Slide Screw/Washer Set. Set includes 1 screw and 1 washer.
-
Yamaha RD400 Throttle Cable Adjuster Cover Replaces OEM #1A0-14169-00-00 (sold each). No longer available from Yamaha, this is a reproduction part.
