-
Yamaha RD350/400/250 Oil Line Clamp. Genuine Yamaha OEM part. Sold each. In original black oil finish, no longer available from Yamaha.
-
Y-boot Adaptors for Larger Mikuni Carburetors
- Install a Y-boot Filter kit on your Yamaha RD with Larger Carburetors
- Increase performance by reducing turbulance generated from pod filters
- Adapts our Y-boot filter kit to fit the larger aftermarket Carbs with a 58mm inlet housing
- Mikuni VM30-34
- Mikuni TM32-34
- Includes 2 adaptors and 2 clamps
- Made from Aluminum. In Lincoln NE, USA
- Sold as a pair
-
Sale!Yamaha RD400F Daytona Intake Boots 2V0-14453-00-00 (pair)
-
Yamaha RD400F Daytona Intake Boots - Pair (Carb to Airbox Boots)
- Brand New Reproduction part - Originals no longer available from Yamaha
- Newly Manufactured, soft, flexible and true to the originals, restoration quality part
- Original Yamaha Part no. 2V0-14453-00-00
-
Fits 1979 Yamaha RD400F Daytona Only
-
-
Brass T-Splitter 1/4"
- Use to route or repair fuel lines, oil lines and air lines
- Barbed ends provide a secure fit
- Made in the U.S.A.
-
Carb Top Boots - Yamaha 1979 RD400F Daytona. Theses are the accordion type rubber boots that go on top of the Daytona carbs. Sold in pairs, reproduction part. Originals no longer available from Yamaha. 2V0-14169-00-00
-
Carburetor Boots - Carb to Airbox joint for Yamaha R5 and DS7. Exact replacement reproduction part no longer available from Yamaha. High quality rubber, fits R5 and DS7 (all years). Includes 2 replacement clamps and 2 replacement springs.
-
Carburetor Boots - Carb to Airbox joint for RD400, RD250. Exact replacement reproduction part no longer available from Yamaha. High quality rubber, fits 1976-1978 RD250 and RD400. Replaces stock part no. 1A0-14453-01-00. Includes 4 replacement clamps. Note the 250 listed is the later Euro RD250 (looks like USA 400).
-
Carburetor Needle Clip for VM, TM or TMX Mikuni carburetors. Sold each. BS32/126
-
Carburetor Top Cable Adjuster - Mikuni. For Mikuni VM carburetors. Sold each. Available in 6mm or 7mm (RD/RZ/R5). Note: 7mm does not include nut. Choose size and quantity, then click add to cart.
-
VM28 Choke Lever Assembly - Genuine Mikuni. Includes 1x each the following parts / part numbers:
- Lever - 360-14175-00-00
- Nut - 278-14174-00-00
- Plate - 170-14178-00-00
- Choke Plunger - 278-14171-00-00
- Plunger Spring - 256-14135-00--00
- O-ring - 93220-09001-00-00
- Choke Plunger Cap - 802-14173-00-00
-
Carburetor Choke Plunger by Mikuni for VM24-28mm carburetors. Sold each.
-
Float Needle Valve Assembly for RD250/350/400. Includes float needle, seat & washer. Metal tip float needle.
-
Float Bowl Drain Washer (gasket) for VM28mm Roundslide carburetors - RD350/RD250/R5 (all) Sold each. Genuine Mikuni
-
Float Bowl Drain Washer - RD350/RD250/R5 (all) Sold each. OEM part no. 278-14117-00-00
-
Float Bowl Drain Washer - RD400 (76-79). This Viton O-ring is a perfect replacement for the original gasket which has been discontinued by Yamaha.
-
Float Bowl Gasket for RD250/350/400. Reproduction gasket.
-
Premium Float bowl gasket for RD250/350/400, mfg'd by Sudco. Premium quality precision cut gasket. Note: color of gasket may vary from time to time.
-
Float Bowl Gasket for Yamaha R5, DS7, also fits new style Mikuni VM28's (28-49). Note: Does not fit original RD250/350/400 carbs
-
Float Bowl Screw for VM24-28mm carburetors. Sold each. Note threaded portion of screw is 15mm (slightly longer then original screws used on RD's, but works fine).
-
Float Bowl Screw set for VM24-28mm carburetors. Sold as a set of 4 screws with lock washers (enough to do one carburetor). Note threaded portion of screw is 14mm (same as original screws).
-
Genuine Mikuin Vent Line, sold each, precut from Mikuni in approximately 11.5" sections, transparent pink color.
-
2 Stroke Oil Injector Nozzle - RD250/350/400 (carb oil injector nozzle). Economy Cycle reproduction item, no longer available from Yamaha. Sold each.
-
Jet Needle Shim for Mikuni 5 Series Jet Needles. Sold each. These shims are used to make incremental adjustments between clips on jet needles used on Mikuni VM carbs with series 5 jet needles (5DP7, 5L1, etc.).
-
Main Jet Washer by Mikuni for VM24-28mm carburetors. Sold each. This washer seats under the main jet (on bottom of needle jet).
-
Genuine Mikuni Needle Valve Assembly for R5/DS6/DS7. Includes float needle, seat & washer. Metal tip float needle.
-
Genuine Mikuni Needle Valve Assembly for RD250/350/400. Includes float needle, seat & washer. Metal tip float needle.
-
Mikuni Vent Tube Anchor Plate - This part attaches to the float bowl screws and holds the vent line. 2 Required per carb.
-
Genuine Mikuni Viton Tip Needle Valve Assembly for RD250/350/400/R5/DS7 & all VM(24-30mm) Carb. Includes Viton tip float needle, float valve seat, does not include washer, available separately. Sold each.
-
Mikuni VM - Air Jet (tap and die) - Convert your pressed in VM air jet to removable type. This kit is also good for chasing/repairing pilot jet thread.
-
Genuine Mikuni Float Needle Valve Seat Washer for RD250/350/400/R5/DS7 & all VM(24-30mm) Carbs. Sold each.
-
Oil Injection Line Clip, 90468-02033-00 OEM Originals $6.99 each or Reproduction Clips - $1.95 each
-
Fuel Rated Plastic T-Splitter 1/4"
- Use to route or repair fuel lines, oil lines and air lines
- Barbed ends provide a secure fit
- Made in the Germany
-
Quad Flow Torque Wings for RD's and RZ's (stock carbs) The Quad-Flow Torque Wing has horizontal and vertical air flow stabilizers which increase air flow, air speed and fuel atomization, thereby increasing performance. Install for maximum performance, then HANG ON! Note: This kit is for twin cylinder engines and includes 2 torque wings Increased power across the RPM range, awesome throttle response. Easy installation, no tuning required. Stainless steel construction, no moving parts.
-
Brand new fresh rubber carburetor boots for Yamaha RD350 and R5. Boots protect the carbs and cables from dust, dirt and moisture. These boots go on top of the carbs where the cable enters the slide. These are not the boots that connect the carbs to the air filter box. These are suitable for any round slide carb for street and dirt motorcycles. Sold in pairs.
-
RD250/350/400 Carburetor Clamp (carb to manifold). This is a high quality alternative to the expensive Yamaha part (17.50), secures carb to manifold. Sold each. Note: The finish on these is yellow/brass, very different from the original olive drab color clamps but they perform just fine at much less cost. The original Yamaha part number was 90460-43053-00, superceded to 90460-43179-00.
-
RD250/350/400 Carburetor Clamp (carb to manifold). OEM Yamaha parts, secures carb to manifold. Sold each. The original Yamaha part number was 90460-43053-00, superceded to 90460-43179-00.
-
Carburetor Boot Clamp. Sold each. Note: The finish on these is yellow/brass, very different from the original olive drab color clamps but they perform just fine at much less cost. Fitment as follows: R5 - Carb to carb boot (2 required per bike) RD250/350 - Carb to Y-boot (2 required per bike) RD400 - Carb to carb boot / Carb boot to air box (4 required per bike) (all years of RD400 including 1979F Daytona)
-
RD350 Y-Boot Intake - Genuine Yamaha Part. Also Referred to as JOINT, AIR CLNR, part no 360-14453-00-00
-
RD350 Y-Boot Intake, Also Referred to as JOINT, AIR CLNR, Yamaha part no 360-14453-00-00, this is a reproduction part.
-
RD350/250/R5/DS7 Carburetor Float, sold each (2 per carb). Genuine Mikuni Part
-
RD400 (all years) Carburetor Float, sold each. Genuine Mikuni Part.
-
The UFO Ultimate Flow Optimizer is a simple, trouble free, aerodynamic piece for stock RZ350/Banshee carbs. The UFO makes a normal round slide carburetor out-perform the more expensive flat slide carburetor by eliminating turbulence and increasing air flow and velocity, creating a highly atomized fuel charge. Normal gains are 3/4 to 1 HP per 100 cc of engine displacement on 4 stroke engines and 1 1/2 to 2 HP per 100cc of engine displacement on 2 stroke engines. (Minimal re-jetting (pilot jet) and tuning are required). Note: This UFO kit is for twin cylinder engines and includes 2 UFO's.
-
VM26-28 Carb Top Gaskets Sold Each. Suitable for RD250/350/400 & others with VM26 or VM28 carburetors. Genuine Yamaha Part.
-
Yamaha CS5 - Carb to Airbox Intake Boots - Pair 337-14453-00-00 reproduction (sold in pairs)
-
Yamaha RD250/350 Carburetor Boot for Low Top Carburetor, sold each. Yamaha OEM part.
-
RD250/350 Idle Screw / Spring Assembly. Includes Screw & Spring. By Mikuni. This is also the correct idle screw/spring for the new Mikuni VM28's.
-
RD250/350 Idle Screw / Spring Assembly. Includes Screw & Spring. OEM Yamaha
-
Yamaha RD250/350/400/R5/DS7 Rubber Choke Plunger Cap (COVER, PLUNGER CAP) reproductin replaces OEM # 802-14173-00-00, sold each
